Die casting is the method used for forcing molten metal into mold cavities under high pressure. Casting is very versatile and hence, is the widest used method for casting a metal. Die casting is same as permanent mold casting the only difference is that the metal is injected into the mould at very high pressure of 10-210 Mpa. This results in a more uniform part, usually good dimensional accuracy and also good surface finish.

The different metals and alloys that can be used in die casting are zinc, aluminum, copper, magnesium, tin and lead. Ferrous metals can also be used for die casting, die casting method is generally used for applications in which a large quantity is medium or small sized parts are required with detail, good dimension and fine surface finish.

There are namely two equipments used for die casting cold chamber and hot chamber process.

Molten metal is a huge part of the cold chamber process as you get to fill a cold chamber of each module with this molten metal. The time exposure provided for the molten metal to plunge the walls of the mold is less. This clod chamber process method is very useful for metals like aluminum, copper and metals that easily alloy with iron at high temperatures.

Hot Chamber process: In the hot chamber process method of Metal Casting , the pressure that is connected to the die cavity is forever and permanently in molten metal. As the plunger moves towards the open position that is towards the non - pressurized area, the inlet port connected to the pressurizing cylinder is uncovered.

The die casting molds which are used in this method are expensive and take usually take long production time. These die casting modules are also called as “dies’

Advantages of Die Casting: The method of die casting gives excellent dimensional accuracy. The dimensional accuracy is as good as 0.1mm for the first 2.5cms and 0.005 for the first inch. Smooth cast surfaces can also be provided with Die Casting. Small and thin walls and can be made using the method of die casting walls as tiny as 0.75mm approximately can be casted. Inserts like thread insert, high strength bearing surfaces and heating elements can also be inserted using the Die Casting method. Metal Casting also helps in reducing or even completely eliminating the use of secondary machining operations. The use of Die Casting method also helps to reduce the production time and a huge number of articles can be produced in a very short time. Die casting method also helps to retain as well as increase the tensile strength of the metal. You can get great strength that is about as high as 415 MPa and that is about 60ksi.
 
Disadvantages of Die Casting: The casting weight is very less hardly between 30 grams and 10 kgs. Also the size of the material that needs to be casted using the Die Casting method needs to small say around 600mm. the high initial cost of Die Casting sometimes has people shying away because there is such a large investment to get started. Die Casting method makes the metal porous up to some extent. In the Die Casting method the thickest section needs to be less than 13mm or 0.5 inches.

Metal Casting ZOne is a new community website all about Home and DIY Metal Casting. If you visit the website today and sign up for free you can get your very own free Metal Casting Basics Guide Book! Visit today at MetalCastingZone.Com right now to get your Free Ebook that is all about Metal Casting and Metal Casting Basics for Free.

Casting Jewelry is a process in which liquid material made from heating metals, is poured in a module, to give the liquid a desired shape. Then the liquid is cooled and a solid object in the desired shape and size is obtained. Casting Jewelry is the latest “in-thing” in the fashion markets. This jewelry is made from different materials like silver, aluminum, gold, bronze, alloy metals and even plated casting jewelry is available.

Casting Jewelry is very attractive and delicate. They are made using machines, but very finely crafted and hand made jewelry is also available in the market. This type of jewelry can be available at a very low, as well as high costs, depending on the design and material and design that you choose. Casting Jewelry is very fragile and should be handled with out most care as it can break easily. With the advent of casting jewelry, the fashion world has benefited a great deal. Today, free flowing designs, multicolored jewelry and even a special made to order jewelry is available in the market.

Before this, it was difficult to cast a metal in a desired shape but today it is as simple as it gets, all you need is a creative mind to create new designs and a group of well qualified workers and good machinery to make your own casting jewelry. This also gives you an option to make your own series of new designs. Casting Jewerly is now used just about everywhere on the globe. With the prices of gold increasing day by day and with the entry of new metal jewelry like platinum, casting jewelry slowly but surely is making a mark in the fashion world. With the cost silver plated casting jewelry, the dream of wearing a new necklace or a new ear-ring everyday is a reality. You can actually afford new set of jewelry everyday. There are also costly models made of pure gold and delicate designs and with embedded diamonds that are available. 

Casting Jewelry is not only about fashion, it has also opened a new avenue for small scale businesses. With proper knowledge and machinery, you can start your own company and make casting jewelry. It does not need any expensive material nor does it need a big capital. A small store room in your house will also be sufficient to set up your casting jewelry work-shop. You can then design your own range or hire a professional jewelry designer to create your range of jewelry.

Casting Jewelry has also helped the educational branch of “jewelry designing” grow considerably. Today it is considered in par with “fashion designing”. Many young students are nowadays looking at jewelry designing as a full time career.

Sometimes you will find that plated casting jewerly may lose its shine or the coating if it is used heavily or on a daily basis. If they come in contact with water regularly, then they can turn black. You can get them re-plated and use them. As casting jewelry is very fragile and delicate, even a slight mishap can change its shape or even break it.

This new websited is all about DIY Metal Casting and Metal Casting Topics and is called Metal Casting Zone. Come by today and join the site for free and you get a free Metal Casting Basics EBook just for signing up! Come by MetalCastingZone.Com Today for your free Ebook on Metal Casting.

When one talks about Oxy-Fuel Cutting or Oxy-Fuel Welding, they mean the process when you cut or weld metals by using pxygen and fuel gasses.  There are some striking differences between these two processes. In the first process, a cutting torch is made use of for heating ferrous metal to a temperature of around 980 degree Celsius. An oxygen stream is being trained on a hot metal that combines with iron chemically which later flows from the kerfs, or cut in the form of slag of iron oxide. In the second process, a ‘welding torch’ is made use of for welding metals.

If a torch takes the air and burns the inside fuel then is really will not be called an Oxy-Fuel Torch. They stand out owing to the use of single tank. This is because oxy-fuel cutting/welding requires oxygen, fuel, and two tanks. It’s not possible to melt some of the metals with single-tank torches. Therefore, you can use these torches all you way for brazing and soldering but they should not be used for welding. A metal-cutting torch is better known as hot blue spanner, blue wrench, hot wrench, smoke wrench, and gas-axe.

Types of Metal Casting Torches: The torch can be defined as the part held and manipulated by the welder to get the weld made. It possesses a valve and connection for oxygen and the same things for fuel gas, a handle to obtain the grip, an integrating chamber (angularly set) where there occurs a mixing of oxygen and fuel gas, with a tip where formation of flame takes place. The fuel gases used along with oxygen include propylene, propane, hydrogen gas, MAPP gas, Liquefied Petroleum Gas (LPG), and the most widely used is acetylene. 

Injector Metal Casting Torch: It can be defined as an archetypal oxy-fuel torch, also known as an equal-pressure torch. It carries out the mixing of mere two gases. The injector torch operates in such a way that high pressure oxygen comes out of the tiny nozzle present in the torch head, and the fuel gas gets dragged towards it via the venturi effect.

Rose-bud Torch: The use of this torch is to carry out the heating of metals for straightening, bending, etc. It is generally used where a huge area requires heating. It produces a rose-bud shaped flame at the end, hence the name. This torch can carry out the function of heating small areas like rusted bolts and nuts as well. However, here, filler rod won’t be used with torch.

Cutting Metal Casting Torch: The head of the cutting torch is used for cutting metal. Its identification details are as follows: The inside of the torch consists of a combination of oxygen and acetylene. It helps in producing flame of a high temperature. What it looks like are three pipes that are affixed to a tube at a 90 degree angle. It also contains an oxygen-blast trigger which blasts away the material during its cutting by the way of providing oxygen.

Welding Torch: The welding torch consists of either 1 or 2 pipes running towards the nozzle without oxygen-blast trigger. As the name suggests, it performs the function of welding.

Metal Casting ZOne is a new community website all about Home and DIY Metal Casting. Come by today and join the site for free and you get a free Metal Casting Basics EBook just for signing up! Stop by the website MetalCastingZone.Com right now to get your Free Ebook that is all about Metal Casting and Metal Casting Basics for Free.

DIY Casting Furnace are nothing but Do It Yourself casting furnaces. One can make variety of furnaces. The procedure of some of them can be described as follows:

DIY Casting Furnace : Theoretically, only three things are required for implementing induction heating: High frequency Electrical Power Source, work coil for generating an alternating magnetic field, and a workpiece-electrically conducive. Really the easiest way is in reality very very complicated. For instance, the work coil and High Frequency source’ should have a matching network in between, to obtain better power transfer. Use of water cooling systems is very common in induction heaters of high power. This facilitates removal of waste heat from the matching circuit of the work coil and the coil itself. This process involves application of control electronics as well. Control Electronics, as the name suggests, controls the heating action’s intensity, thereby ensuring consistent results. Really you are getting protection from bad working and operating conditions.

Usually, the incorporation of work coil takes place into a resonant tank circuit. There are innumerable advantages of this. The first advantage is that any one of the parameters, i.e. voltage or current is made sinusoidal. This causes fewer losses to inverter by the way of allowing it getting benefited from either zero-current-switching or zero-voltage-switching corresponding to the arrangement chosen. The visibility of sinusoidal waveform at work coil gives the proof of purity of signal. There also occurs less interference of radio frequency with the equipment in its vicinity. It’s up to the designer to choose one amongst several resonant schemes.

DIY Bronze Furnace: The making of DIY Bronze Furnace involves taking silica bricks of 9 inches X 4 ½ inches X 2 ½ inches in the first place. After that, one is supposed to put a steel plate having dimensions 18 inches X 24 inches at the place where he intends building the furnace. In other words, the steel plate should be used as a base. The construction of furnace should start thereafter. It is advisable to keep the circumference of the furnace as 14 inches. A small hole of diameter 3 inches should be made at a height of 5.5 inches above the floor. Eleven and a half inches should be the height of the cylindrical furnace from floor to the top. This hole is to be used for inserting the burner.

The cutting of the burner port should be done in such a way that it acts as a perfect tangent to furnace. This should be done in order to make the flames whirl around crucible, thereby hitting it indirectly. The peculiarity of bronze casting is emission of toxic fumes. Thus, as you can imagine you really need to cast in areas that have very good ventilation. The process of casting really means that you should wear safety clothing and classes. After the completion of furnace (including the cutting of hole to get the fitting of one’s biggest crucible enabled), it should be permitted to dry. At that time, trawling of water, vermiculite, and kaolin clay on the exterior is recommended. The immediate use should be strictly avoided, as it may develop cracks. After drying, let the furnace be heated slowly to reduce ‘kaolin paste’ cracking.
 

Metal Casting ZOne is a new community website all about Home and DIY Metal Casting. Come by today and join the site for free and you get a free Metal Casting Basics EBook just for signing up! Come by MetalCastingZone.Com Today for your free Ebook on Metal Casting.

There are various casting processes being implemented now days. The oldest amongst them is sand casting. Metal Casting is also widely used. They can be described as follows:

Sand Casting: Sand Casting involves formation of mold from a mixture of sand and to pour a casting liquid, most probably, a molten metal into mold. Then, you wait a while and let the metal harden up so then you can remove the mold. Sand molding consists of two types: green sand method and air set method. The first one consists of mixture of clay, moisture, silica, and many other additives. The second one consists of mixture of dry sand and other materials, not moist clay. They are mixed with the help of a quick curing adhesive. When all of these materials are used together, it is a process called air set.

At times, there is temporary plug placed to pour the fluid which is to be molded. Air-set molds usually form molds consisting of two parts-the bottom and the top. The mixture of sand gets tamped down after its addition. It does not generate any by-product. After the solidification and cooling of metal, the mold gets usually destroyed. This is because its removal involves a lot of breaking and cracking. The casting accuracy depends a great deal on the sand and the process of molding used. Castings composed of green sand result into formation of rough texture on casting surface, and this characteristic makes them easily recognizable. Air-set molds produce smoother castings.

Many a times, the casting process results in losing of components of sand mixture. It is possible to reuse green sand by the way of adjusting the composition to get the lost additives and moisture replenished. The entire pattern itself is eligible to be reused for producing novel sand molds. The method of reuse can be continued for an indefinite period. In 1950, casting process got automated partially. They have been in great demand for developing production lines since then. 

Spin Casting: Sand Casting is better known as Centrifugal Rubber Mold Casting (CRMC). It implies utilization of centrifugal force for producing castings out of rubber mold. As a customary practice, a mold having shape of a disc gets spun through its ‘central axis’ at a pre-decided speed. The material used for casting is usually thermoset plastic in the liquid form or a molten metal. It gets poured into the mold through the opening at its centre. Corresponding to the solidification of metal, or the setting of thermoset plastic, the spinning of the filled mold takes place.

Normally, organic rubber or vulcanized silicone is used as a mold-making substrate in spin casting. Vulcanization takes place in the middle of process of mold-making. After the successful completion of vulcanization process, venting and gating must be undergone by the mold. This implies carving of channels for ensuring proper material flow and air during the course of casting. The best tool to use to preform the two processes just mentioned is either a scalpel or a knife. The mold complexity is directly proportional to the time required in implementation of venting and gating.  

Metal Casting Zone is the premiere place to go to discuss everything about Metal Casting, Home Casting and anything else Metal Casting. Come by today and join the site for free and you get a free Metal Casting Basics EBook just for signing up! Come by MetalCastingZone.Com Today for your free Ebook on Metal Casting.

The Garmin Nuvi 760 GPS Navigation System is among the top items available for navigations. The maps that are part of your the Nuvi 760 cover all of North America so you can journey to the United States, Canada, or Mexico with your navigator to guide you.

Features

The display on the Garmin Nuvi 760 give you a large 3.8 by 2.25 screen that is complete with a backlight and a glare-resistant screen. The readout even offers a great resolution of 480 by 272 pixels ands a 3-D image display.

Your Garmin 760 also offers an FM radio transmitter to give you the ability to keep up with the most current real-time traffic reports that allow you to miss high-density traffic areas in the city. All of the data that you must input on the unit is on the touch screen so the shape is compact with clean lines and a nice ball socket build.

You attach the Garmin Nuvi 760 to your windshield with a small suction cup that can be taken down with ease when you are ready to get out of your car. The small size is good when you are afraid to leave the system behind; the navigator will effortlessly slide into a pocket or tote as you go to work or to the store.

Extra Features

The Garmin Nuvi 760 Travel Assistant has a feature that can be use to keep track of the most frequently used routes. For example, if you visit hotels on a regular basis, you can save the hotel address in the unit and then simply put in your destination address for the fastest and most efficient route.

You can even store the names of your most-visited diners and boutiques in the navigator to get to these places with no trouble in a strange city. This is a very helpful feature when you wish to find a certain product that is not sold in some places.

The Nuvi 760 is also a good tool to use if you experience trouble rediscovering where you have left your car in a sizable city or parking garage. The unit will automatically remember where you parked by saving the last point that the unit recalls. This is a useful feature that is not included in the earlier Garmin Nuvi items.

Adding Features and Maps

If the Garmin Nuvi 760 GPS Navigation System that you have right now needs to be modified, the only step is to navigate to the official website to load current maps and goodies onto the product. A few updates must be bought, such as travel instructions and maps. You Nuvi 760 package will provide a USB cable so that you can easily attach your unit to your PC for updates.

You will also have the option of selecting the location of the touch screen letters on your Nuvi 760. Most consumers are accustomed to a QWERTY keyboard and find it faster to utilize this style when entering information.

Casting can be defined as a process of manufacturing, which implies pouring of a ‘liquid’ material into ‘A Mold’ containing a desired shaped hollow cavity, and then made to solidify. What needs to be done to finally complete the process is to take out the casting and break it apart so you can see your finished project. The use of casting is ‘forming hot liquid metals’ or numerous metals that are cooled after having the components like clay, plaster, concrete, and epoxies mixed. Complex shapes are normally made by casting, as other methods are not feasible. Casting came into being around 6000 years ago. ‘Copper Frog’ is the most ancient casting existing till date since 3200 BC. The process of casting has two distinct subdivisions: non-expendable and expendable mold casting.

‘Non-expendable’ mold casting: This technique is inclusive of at least 4 distinct methods: continuous, centrifugal, die, and permanent casting.

Continuous casting: Continuous Metal Casting can be defined as a refined process of casting for high-volume, continuous production of ‘metal sections’ with constant cross-section. The pouring of molten metal into a water-cooled, open-ended copper mold takes place. This allows a ‘layer’ of ‘solid metal’ to be formed above the ‘still-liquid’ center. Continuous casting is widely accepted due to its cost-effectiveness. The metals continuously cast are aluminum, copper, and steel.

Centifugal casting: Centrifugal DIY Casting is independent of both-pressure and gravity. This is because its own ‘force feed’ is created by the way of using a ‘temporary sand mold’ in ‘spinning chamber’ at 900 N. Lead time is variant with respect to application. True- and semi-centrifugal processing allow 30 to 50 pieces/hr. The batch processing has an upper limit of around 9000 Kg (practically). Before, this method that is being discussed was used to Cast Railroad Wheels. It was developed by the company called ‘Krupp’. It had a German origin. Jewelry is normally cast by this method.

Die-casting: Die Metal Casting can be defined as a process of ‘forcing molten metal’ into cavities of mold under high pressure. Aluminum, Copper and Zinc are what really make up most of these castings. It is even possible to make die castings of metal. The method of die casting is used where finer parts are needed.

‘Permanent Mold Casting’: This casting is made up of non-ferrous metals. It requires some time to set up (some weeks), after which the production rate of about 5 to 50 pieces/hour-mold is achieved. The coating of ‘acetylene soot’ is applied to steel cavities. This helps in removing the work piece easily and promoting longer life (of tools). Permanent molds possess a limited life span. For worn molds, replacement or refinishing is required.

Expendable mold casting: ‘Expendable Mold casting’ can be referred to as a standard classification inclusive of the following:

Sand casting: It is amongst the simplest and most popular casting types used since ages. It involves very small size operations. The bonding of sand takes place by use of clays (as in ‘green sand’) or ‘polymerized oils’, or ‘chemical binders’. Recycling is easily possible.

Plaster casting (for metals): There is no difference between plaster casting and sand casting, except the fact that plaster is used in place of sand. Similarly, there are also plastic and concrete castings.

Metal Casting ZOne is a new community website all about Home and DIY Metal Casting. A Metal Casting Basics Ebook is available for free to anyone who comes by the site and joing, which is also free! Come by MetalCastingZone.Com Today for your free Ebook on Metal Casting.

There are several types of Casting Furnace which include Electric Arc furnaces, Blast furnaces, Cornwall Iron Furnace, etc. Here’s a quick review of some of them.

Electric Arc Furnace: This furnace can be described as a furnace heating charged materials by the way of an electric arc. These furnaces exist in all the sizes-right, from the smallest one having a capacity of around 1 ton to the largest one having a capacity of 400 tons. The former one is used in foundries to produce cast iron products, whereas the latter one is used for secondary steel making. The ones used by dentists and in research laboratories might be having capacity of a few grams only. The electric arc furnace can have temperatures risen up to 1800 Celsius. A man in France named Paul Heroult was the first person to creat an electric furnace and the year was 1907. The commercial part of these furnaces was established in the United States of America. Electric Steel was one of the first special products that was used to make spring steel and machine tools. Calcium Carbide was also prepared in these arc furnaces. It (calcium carbide) was used in carbide lamps.

This Casting Furnace comprises of a refractory-lined vessel, normally water-cooled in huge sizes, having a covering of a retractable roof, through which the entry of graphite electrodes takes place. The numbers may be many or few. The furnace is divided into 3 sections: the shell, consisting of lower steel bowl and sidewalls, the hearth, consisting of refractory lining the lower bowl, and the roof, that can be water-cooled or refractory-lined, and can easily be shaped into a spherical section or conical section (frustum). A refractory delta is also supported by the roof at its center, by the way of which graphite electrodes make an entry.

The process of operation starts with delivery of scrap metal to scrap bay which is located adjoining melt shop. After that, the loading of scrap into huge buckets or baskets takes place. The next step is to carry this basket to the melt shop. Now is when the charging takes place here. The electrodes should be allowd to enter and put onto scrap after the charging is completed. This causes the arc to be struck. Lower voltage is preferred for this part (of operation) to provide protection to the walls and roof against arc damage and excessive heat. After having the electrodes reached the heavy melt, shielding of arcs by scrap takes place. This enables a rapid formation of molten pool, thereby decreasing tap-to-tap times. Oxygen is also allowed to enter.

Casting Furnace : It can be referred to as a kind of metallurgical furnace, through which the process of smelting takes place. This produces metals, normally iron. These furnaces trace their origin to China (around 500 BC). They were also found in Belgium and England later. They do not have any special mode of operation. The metals get melted by heating only. Generally, iron is melted in these furnaces. The chemical reaction can be explained as follows:
                Fe2O3 + 3CO -> 2Fe + 3CO2

Metal Casting ZOne is a new community website all about Home and DIY Metal Casting. Come by today and join the site for free and you get a free Metal Casting Basics EBook just for signing up! Come by MetalCastingZone.Com Today for your free Ebook on Metal Casting.

In a word, no.  You will probably need to know how to quickly scan your G-Code if you are having problems during your machining simulation.G-Code and CNC programs are throwaway programs for the most part.  What do I mean by that?  Let me explain.

Let’s look at a specific design.  Let’s say a 12” by 12” square.  You build your model, run it through your CAM Software and create a CNC Program made up of G-Code instructions to your machine.  Say tomorrow the job requirements change to a 24” by 24” square.  Do you go into your G-Code line by line and change the code?  Most people wouldn’t.  They would go back into their CAD or CAM program and scale the square up to 24” by 24”.  Then post-process the job again to get their new gcode.

There are some people that would do this editing line by line because the design is simple.  Now think of a complex shape and what scaling it up or down would entail.  This would include massive changes to the G-Code and reviewing it line by line.  We are talking thousands of lines here vs. Going back and quickly changing the size of the model, then creating some new G-Code.  And that is why G-Code is throwaway.  Use it over and over when you can, but don’t fret over archiving it if something changes.  It is much better to make a copy of the design (CAD File) in its original state and save that somewhere.  That is much more useful.

Post Processing??? - Now you have me worried.With all the differences in G-Codes and and M-Codes, how will we ever keep it straight?

Don’t worry about that.  The CAM program you choose will have many Post Processors.  Post Processors are like translators.  They help the CAM Program spit out the right gcode for your specific machine.What you have to do is select the right post processor before you create the G-Code.  That is simple.

Most CAM programs have many machine specific post processors already loaded.  All you do is go to the list of them and click on your machine to select it.  If you build your own CNC Machine, there are generic post processors loaded for different types of machines.  Usually you pick a generic one and modify it a bit with a little testing.  You are making sure a move in the X-Axis positive direction really means what you want it to mean.

CNC information community:
Do you want to know more about CNC, head on over to http://www.cncinformation.com
You can join for Free and you get two free CNC ebooks. One is a GCode Quick Guide and the other is the CNC Info Site eBook. You also get the free CNC videos…Image to CNC Art when you join the community.

What I used to do…
I was in the stone ages before I found creative design software.  I would actually hand lay out a template on a piece of paper.  Then cut it out.  Next, I would tape the design onto a piece of steel and trace around it with a Sharpe Marker.  Finally, I would cut out the piece I wanted.

No matter what, it was never exact.  There would always be something wrong.  Things like wavy lines, gouges and “unique parts” were the norm.  Measurements were never as exact as I would have liked either.  That usually caused some fit-up issues, followed by some grinding.  If you know anything about fabrication, grinding is the enemy of your time.

Why use CNC art design software?
I knew there had to be a better way so I found some design software to try out.  Yes, it does take some time to learn.  Think about it, like anything else in life, something that is worth it takes some time.  This is also the situation of taking one step backwards to move ten steps forward.

Great advantages of using design software:
Saved file you can use over and over
Transferred the unique design to other people
Can use exact measurements
Repeatability in design

Here are disadvantages of using creative design software:
Cost money
Takes time to learn
May not be the quickest way of making something if it is a “One Off”

My Definition of Design Software
If you are an engineer, you will probably consider CAD Software as design software.  That is true.  But what I am talking about here is “Creative” Design Software.  These software packages are used by creative types for print, web design and logo design.This software is great for creating CNC artistic designs that flow in some way.
Design software can be boiled down to what it is good at.  If you want to make a square with a hole in it or a triangular gusset, then CAD type design software works great.  If you want to cut out a Cowboy on a Horse, then “Creative” Design Software is the only way to go.

Here are some examples of work for “Creative” Design Software:
CNC plasma art
CNC Artwork
Signs
Engraving

CNC Information Free Community Site:
If you would like to know more about CNC, head on over to http://www.cncinformation.com
Join today and get two free CNC eBooks. One is a GCode Quick Guide and the other is the CNC Info Site eBook. You also get access to the Free Video Series…Image to CNC Art when you join the community.